Jump to content
Call us (951) 749-6477

Guide ยท Riverside

Earthquake gas shut off valve installation: what to know first

An earthquake valve goes on your house gas line, installed by a contractor with a permit, not by you and not by SoCalGas. Here is how the job works and what to confirm.

Gas meter, then a seismic shutoff valve on the line just after it, then house piping to appliances.

Putting in an earthquake gas shut off valve on your own would break the rules, because it is gas piping, and a contractor with a permit does that work. You can still learn the job so the quote makes sense. This page sits within the broader section on gas lines in Riverside and explains who does what and what to ask.

Who installs the valve, SoCalGas or a plumber?

A contractor you hire installs it, working past the meter on your property. SoCalGas says it no longer installs earthquake shut off valves for customers and does not permit customer-owned equipment on its facilities. The valve is mounted on the house line after the meter, which leaves the gas company's pipe and meter alone.

That split also explains a safety rule. Operating the meter shutoff belongs to SoCalGas or its contractors alone, so after a quake do not turn that one off or on unless someone has shown you how. Learn where the valve is, and note the emergency number that SoCalGas lists for suspected gas leaks, 1-800-427-2200. If you notice a gas odor, go outdoors first and phone from there.

SoCalGas serves Riverside, Moreno Valley and Loma Linda, so the same division of duties applies in all three cities.

What happens during the installation?

A plumber experienced with gas chooses a valve approved for earthquake use, fits it to the gas line right after the meter, and then pressure-tests the line for leaks. Permits are normal for gas work. After an inspection, you receive the paperwork and instructions on how to reset the valve once it trips.

Three boxes in order: check the site, shut gas at the meter, then install, test and restart.

The visit looks like this. First the plumber checks the meter location, the line size and the clear space around the pipe, because the valve needs room and the right orientation. Second, gas to the house is shut off at the meter, which is why the appliances go dark for part of the job. Third, the valve is threaded in, the line is tested, and the pilot lights and appliances are restarted. The plumber should leave you with a written description of the reset procedure.

Step-by-step instructions for gas pipe work are not published here, since mistakes cause fires and explosions. To learn something useful, have the plumber demonstrate the reset procedure when the visit wraps up.

Which type of valve is the right one to request?

Ask for a seismic shutoff valve, which closes when ground shaking reaches a set strength, and know that an excess flow valve is a different device, which closes when gas flow suddenly surges, for example after a line break. Many people mean the first when they say earthquake valve. Ask the plumber which one the quote covers and whether it carries the approval your building department expects.

Ask for the model name and the approval listing in writing. Valves should not be installed in a utility meter vault. If an inspector or an insurance company asks for proof, you will need the model details.

Is a valve required in Riverside, Moreno Valley or Loma Linda?

No city rule for these three cities could be confirmed from an official page, so none is stated. SoCalGas tells customers to contact their local Building and Safety department for earthquake valve requirements. The safe step is to ask the city building office that covers your address before you buy.

Riverside Building and Safety is at (951) 826-5800 and Moreno Valley Building and Safety is at (951) 413-3350. Loma Linda lists (909) 799-2836 for permit questions. A lender, an insurer or a buyer's inspector can also ask for a valve even when the city does not. Anything you decide to add, such as extra strapping on the water heater, is worth discussing at the same visit, because California rules require earthquake strapping on water heaters.

What should I expect to pay for the installation?

No published guide we could read prices an earthquake valve alone, so no dollar figure appears here. The cost turns on the valve, the pipe size and how easily the side of the house with the meter can be reached. Ask for the valve, the labor and the permit as separate lines; the written quote sets the price.

For context only, gas piping jobs in general are covered on our gas line cost page, while the code details behind gas piping are explained in residential gas piping codes. Neither is a quote for a valve.

Common questions

How much time does the installation need?

A valve install is mostly a short visit, with the exact time set by the pipe, the meter access and whether an inspection falls on the same day. Gas to the house stays off during the work, which means doing without hot water or heat for a while. At booking, the plumber can offer a time window.

What questions come before hiring an installer?

Check whether the quote covers the permit and inspection, which valve model it names, and who demonstrates the reset steps. Permitted work in California falls under the contractor license rule, so request the number and look it up on cslb.ca.gov. Get the price in writing before work begins.

Must someone be home during the work?

Yes, an adult needs to be home, as the gas is cut at the meter and the appliances must be relit when the work finishes. Having someone on site also means the plumber can walk you through the reset procedure. Clear the area around the meter and any gas appliances before the visit.

What happens after the valve trips?

After a quake the valve may close and stop gas to the house. Do not relight appliances until a plumber or the gas company confirms the line is safe, because gas may have leaked. SoCalGas advises contacting a qualified professional or SoCalGas to reset it, so ask the installer to show you exactly how. Whenever gas is in the air, step outside and ring SoCalGas.

Sources used

Page updated