Jump to content
Call us (951) 749-6477

What it costs ยท Riverside

Plumber gas line prices in Riverside

What gas line work costs per job and per foot, according to published guides, and what makes one quote double another. We'll arrange a local plumber to price your job in writing.

Get a quote

Plan of a house with a gas line from the meter branching to a range, water heater and dryer.

A gas line job in Riverside generally runs from several hundred dollars for a short extension to about two thousand for longer or more involved runs. The two guides we read put the whole range at $120 to $2,000, with averages of $558 to $800. Read the gas line plumbing page for what the work involves, then use this page to judge a quote.

Typical plumber prices in Riverside

Published guides put a typical gas line job at $500 to $2,000, with an average near $800 (Fixr, updated August 29, 2025). An older Bob Vila guide, updated February 29, 2024, lists a $120 to $1,350 span and a national average of $558. These are national guide figures, not Riverside rates and not what we charge.

Job or unit Guide figure Source and date
Typical gas line job $500 to $2,000 (average $800) Fixr, August 29, 2025
Wider spread across jobs $120 to $1,350 (average $558) Bob Vila, February 29, 2024
Extending an existing line, per linear foot $10 to $20 Fixr, August 29, 2025
New installation, per linear foot $15 to $25 Fixr, August 29, 2025
Replacing an old line, per linear foot $23 to $35 Fixr, August 29, 2025

The written quote sets the price. The table tells you whether a figure is believable, not what your house will cost.

What does a plumber charge to repair a pipe?

Fixing a gas pipe is priced like the installs above: short repairs near the low end, long replacements near the high end. For water pipes the same logic holds, and the hourly rate guides give the starting point; see plumber prices for those. A leaking gas fitting is different from a leaking water fitting, because a gas odor is an emergency well before it becomes a pricing question.

Smelling gas means leaving the building, phoning SoCalGas on 1-800-427-2200 from a safe spot, and dialing 911 if you feel endangered. Leave switches alone, light nothing and avoid phones indoors. Cost conversations start after the line is safe.

Which factors raise or lower the price?

Length, pipe material, access and permits do most of the damage to a budget. A run of ten feet in an open garage is a short job. A line that crosses a slab, a finished wall or a yard needs cutting, trenching and patching, and the per-foot rates in the table climb toward the replacement range.

Four cost drivers, pipe length, appliance count, access and permits, all feeding one written quote.

Other price drivers worth asking about:

  • Appliance count. A range, a dryer and a water heater share a line, and the pipe size has to support them together.
  • Pipe type. Black iron, corrugated stainless tubing and coated copper behave differently and cost differently. The local gas code and the permit office decide what is allowed.
  • Shutoff and pressure test. A pressure test belongs in the quote, not in an extras list.
  • Permit and inspection. Gas piping typically requires a permit, plus an inspection before the line goes into service; the city's building office can tell you what applies.

Older houses in Downtown Riverside, the Wood Streets and Arlington may carry gas piping that has been added to over time. Newer homes in Orangecrest or east Moreno Valley may have simpler layouts and access. Neither fixes a number: the plumber who looks at the house decides.

How much does a seismic gas shut-off valve add?

No dependable published installed price for a seismic gas shutoff valve turned up in the guides we could read, so we will not quote one. Treat it as a small add-on to a gas job, and ask for it as its own line on the quote. The seismic gas shut-off valve page explains how the device works.

What is the hourly rate for gas work?

Hourly pricing for gas work tracks the general plumbing range, roughly $75 to $150 for typical jobs in the national guides. "Gas Safe" is a United Kingdom registration and does not apply here. In California, the state's licensing board requires a contractor license for any job reaching $1,000 once labor and materials are added up, or any job needing a permit. Gas piping usually needs a permit, which means a contractor license usually applies; confirm with your city.

Before work starts, get each business's contractor license number and look it up on the CSLB website.

How to compare quotes

Lay two or three written quotes next to each other and weigh scope before price. Does each include the permit, the pressure test, the shutoff valve, and patching of any wall or flooring that was cut? Are materials listed, with pipe type and size? Does the quote say who schedules the inspection?

A very low number with a short scope is a warning, not a bargain. A quote at the top of the range with a long, clear list may cost less in the end. Ask how the price changes should the plumber discover corrosion or an undersized line mid-job, and get the answer in writing.

Book a plumber quote

Tell us about the job. We'll arrange a visit and a written quote before any work starts.

Lets the business see where the job is before they quote.

We earn a referral fee from the plumber who gets your job. You pay us nothing.

How do natural gas pipe and flexible connectors fit in?

The connector is the short flexible length joining a rigid gas line to an appliance such as a range or dryer. These parts cost little and swapping one takes little labor, but a connector is also a place where leaks start. Replacement is part of a gas job, not a casual DIY fix, and local codes decide the type and length.

The natural gas line pipe inside a home is rigid or semi-rigid, and sizing depends on the appliance load and run length. Page on residential gas piping codes goes into the rules. If you have a doubt, call the plumber, not the hardware store.

Common questions

What is the typical duration of a gas line job?

A simple extension or appliance hookup may take just a few hours, whereas a longer run or a replacement can eat up most of a day or longer. Time also goes to the pressure test and the permit inspection, since the line stays off until it passes. Ask the plumber for a schedule that includes the inspection.

Which questions should I put to a gas piping contractor?

Request the contractor license number, find out how the permit is handled, which pipe material will be used, whether the pressure test is in the quote, and who patches walls or flooring afterward. Then ask how the price shifts if the existing line proves undersized or corroded. Write the answers down.

Do I need to be home during the gas work?

Yes, in most cases. An adult must let the plumber in, consent to the gas being shut off for a while, and stay available for questions. Someone should also be present for the inspection if the city asks. Plan for the appliances on that line to be out of service for part or all of the day.

Sources used

Page updated