Smelling gas means getting out of the building before anything else. Then phone SoCalGas at 1-800-427-2200 from outdoors, and dial 911 if you are in danger. Every other gas job, whether it is moving a range, adding a dryer line, running a barbecue line or replacing a water heater connection, goes to a contractor California permits to do it, with a permit and an inspection to follow. We pass your request to a local plumbing business for the job. The full list of services is reachable from Rubidoux Ridge Plumbing.
What work does a gas plumber handle?
A gas plumber installs, moves, tests and replaces the pipes, valves and connectors that carry natural gas to appliances. Common work includes running a new line to a range, dryer, fire pit or outdoor kitchen, a replacement water heater hookup, a shutoff valve, a line pressure test after remodeling, and repair of a leak found by a utility or inspector.
This is no place for do-it-yourself work. In California a contractor license is required for jobs that need a permit and for jobs whose labor and materials reach $1,000, and gas piping normally needs a permit. To verify a license number, use the California Contractors State License Board site, cslb.ca.gov. For line types and sizing, see the pages on gas line work and residential gas piping codes.
The gas utility handles its own equipment up to the meter, and the piping on your side is a matter for a contractor. SoCalGas serves Riverside, Moreno Valley and Loma Linda, according to its cities-served list. To confirm who serves a specific address, check your gas bill or ask SoCalGas.
How do I tell whether a job is gas work?
If the job connects to, moves or removes a pipe carrying natural gas or propane, it is gas work. That includes the flexible connector behind a stove, a dryer stub, a water heater gas supply, a manifold, a shutoff and an outdoor line. Replacing a burner assembly inside an appliance counts as appliance repair, a different trade.
Gas work signals to watch:
- A rotten-egg odor, which is added to natural gas so you can notice a leak.
- A hissing sound near a pipe or appliance.
- A pilot that keeps going out, or yellow flames where blue ones belong.
- Dead grass or bubbling in wet soil near an outdoor line.
- Soot around a water heater or furnace.
- A flexible connector that is kinked, corroded or very old.
Any of these is a reason to stop using the appliance and call. A strong odor means exit first. Another option is an automatic valve that closes the supply in a large quake, described in emergency gas shut-off valves for earthquakes.
What drives the cost of gas plumbing work?
Fixr's "Gas Line Installation Cost" guide, updated August 29, 2025, puts a typical job at $500 to $2,000, average about $800, with per-foot figures of $10 to $20 for extending a line, $15 to $25 for a new installation and $23 to $35 for a replacement. These are national guide figures, not our fees and not Riverside plumber rates.
The written quote sets the price. Distance from the meter or manifold, pipe material, trenching or wall opening, the number of appliances, the permit fee, and whether the existing line must be upsized are what move it. Inspections are a smaller line: Fixr's plumber guide says most inspections run $100 to $225. More detail is on the gas line cost page and the plumbing inspection cost page.
Is a permit with inspection needed for gas work?
Generally, yes. New lines, relocations and water heater replacements are normally permitted work, and before gas flows the inspector reviews the pipe, supports, shutoffs and leak test. In Riverside the permit office is Building and Safety, (951) 826-5800. We could not confirm a Moreno Valley or Loma Linda water heater rule from a city page, so call the local division to ask.
The contractor usually files for the permit and books the inspection. Put that to every bidder: who files, and who needs to be home when the inspector comes. Do not ask anyone to bypass the permit to save a few hundred dollars. An unpermitted gas line can complicate home sales and insurance claims, and more important, nobody has checked that it holds pressure.
Earthquake strapping is also mandatory for California water heaters, which matters when a gas unit is replaced and the new one is set in place.
What about backflow testing?
Backflow testing is a different service, though people often search for it in the same breath. It examines the device that stops irrigation, fire sprinkler or commercial plumbing water from reversing into the drinking supply. Your water supplier usually sets which properties need a test and which testers it accepts, so ask the supplier before you book anyone.
No single local testing rule could be confirmed here, so ask your water utility: Riverside Public Utilities, Eastern or Western Municipal Water District, Box Springs Mutual or the City of Loma Linda depending on the address. The test uses a calibrated gauge on the device and the tester files a report. Related reading: backflow testing services, the page on backflow prevention testing and how a backflow test is done.
How do I know a gas plumber is needed?
Call one when an appliance is being added or moved, when a connector is corroded or kinked, when the pilot misbehaves, when you smell gas faintly and it comes back, or when a remodel has opened a wall with gas pipe in it. A pressure test is also a good idea after any earthquake that moved the house or shifted appliances.
Older homes around Downtown, the Wood Streets and Eastside can have older gas lines, and some may have been extended by earlier owners. Tract homes from the 1970s to 1990s in Moreno Valley and La Sierra can have added barbecue and fire pit lines too. A plumber can check what is in the wall, test it with a gauge and tell you what is code today.
Common questions
How long does a gas plumbing job take?
Which questions belong in a gas work interview?
Must I be at home during the gas job?
What number do I use for a gas odor?
Can I move my own gas line?
Guides in this section
- Backflow prevention testing
Got a backflow device on your sprinklers, pool line or water main?
- Backflow testing
Who needs backflow testing, what the annual test involves, how to book it fast and how permits and gas codes fit in for Riverside, Moreno…
- Permits, codes and inspections
Backflow testing in Riverside is done by an approved tester, not by you.
- Costs
What a plumbing inspection, camera scope or backflow test costs, when a city permit is required in Riverside, Moreno Valley and Loma…
- Residential gas piping codes
What the code asks of home gas piping in Riverside County: permits, shutoffs, sizing, testing, inspection and who may do the work.
Sources used
Page updated