Because a repipe replaces all the supply lines, house size drives the price more than anything. Two materials dominate today: PEX, a flexible plastic tubing, and copper. Below you will find national guide figures, a side-by-side comparison and the local conditions that move a Riverside quote. For the full process, start with our repiping guide.
What do guides say a PEX repipe costs?
Bob Vila's guide on PEX versus copper, updated July 23, 2025, gives about $4,000 to $6,000 to repipe an average two-bath, 1,500-square-foot home with PEX. A separate Bob Vila repipe guide from April 24, 2023 gives a broader whole-house range of $1,500 to $15,000 with a national average of $7,500. The 2023 page is older and weaker, so lean on the 2025 figure.
These are national guide figures, not local rates and not what we charge. The written quote sets the price. Read the PEX number as a baseline for a modest house with easy access. More square footage, a second story, finished interiors that are hard to open or extra fixtures push it higher, while a compact house with open access may come in lower.
Which costs more, PEX or copper?
On the same two-bath, 1,500-square-foot house, copper costs roughly double what PEX does in the 2025 comparison. Pipe prices and labor both feed that difference, and a written quote shows how a plumber splits the two. Materials alone show the gap in the 2023 guide, listed in the table below.
| Material | Whole-house, 2-bath 1,500 sq ft | Materials per linear foot |
|---|---|---|
| PEX | $4,000 to $6,000 (Bob Vila, Jul 23, 2025) | $0.40 to $2 (Bob Vila, Apr 24, 2023) |
| Copper | $8,000 to $10,000 (Bob Vila, Jul 23, 2025) | $2 to $8 (Bob Vila, Apr 24, 2023) |
Per-foot figures cover materials alone, leaving out labor, permits, wall repair and fixtures. For durability and water quality, read PEX vs. copper.
What would copper run for my house?
The same guide puts copper for a two-bath, 1,500-square-foot home at the figure in the table. For a larger three-bath house no verified figure turned up, so we will not guess; a plumber counts fixtures and measures runs. Copper has a long record in houses, but metal prices swing, so ask how long a quote stays valid.
Soldered joints take time, which may be part of the labor gap. A house that already has copper with a few pinhole leaks may need only partial work, which costs less than a full repipe, and testing by a plumber can show if the leaks are isolated. Water chemistry may play a part: the city utility's 2025 report lists average hardness of 197 mg/L (about 12 grains per gallon), and chemistry can contribute to pinholes in copper over the years.
Is water flow through PEX as good as through copper?
PEX bends, needs fewer fittings and can be fished through walls, which can trim labor. Flow hinges on inside diameter and layout, and PEX can have a slightly narrower bore than copper of the same nominal size, which is why lines are often sized up. No flow chart we could verify is printed here; have the plumber show the sizing for your fixtures.
Pressure and flow at the tap depend on the whole system: the street pressure, a regulator and the longest run. See low water pressure if that is your concern. A repipe with properly sized PEX or copper can improve pressure compared with old galvanized pipe, because rust-narrowed lines are replaced.
What does polybutylene replacement cost?
No separate guide figure exists that we could verify. In practice it is a repipe, so use the PEX or copper numbers above. Some houses built in past decades got this gray plastic, which is said to fail at fittings, so a plumber can check whether an older home has it.
We could not verify an active replacement program, so we do not describe one. Signs and options are in polybutylene replacement, and older steel pipe from earlier eras is covered under galvanized pipe replacement.
What about a mobile home repipe?
We found no verified guide figure for repiping a manufactured home, so we print none. A smaller footprint helps, though crawl access under the floor, the existing pipe and the layout reshape the work. A plumber has to see the home to price it, so give the type, size and age in your request.
Some parks have rules about contractors and about shutting off water for the community, so ask management first. If the work involves the park's supply line, the park may handle that part. Include any records you have of earlier repairs, since they help a plumber judge whether a partial repair makes sense.
What else changes a repipe quote in Riverside?
Four drivers: fixture count, how easily walls open, whether any pipe runs under a slab, and how much drywall repair you want included. Older homes in Downtown Riverside, the Wood Streets, Arlington and Eastside may have plaster walls, crawlspaces and mixed pipe materials. Newer tract homes in Orangecrest and east Moreno Valley may be easier to open.
Permits matter too. The city's work-exempt-from-permits handout says replacement of piping behind the wall face or below the floor requires a permit in Riverside, and Building and Safety is at (951) 826-5800. A repipe also clears California's $1,000 line for contractor licensing, which counts labor plus materials. Ask who obtains the permit and if inspection time is included in the quote.
Common questions
How many days does a repipe take?
Is PEX cheaper than copper for repiping?
Which questions come first when choosing a repipe contractor?
Does the quote include drywall repair?
Can I do a PEX repipe myself?
For the wider picture, start with Riverside plumber.
Sources used
- PEX vs. Copper, Bob Vila, updated July 23, 2025
- How Much Does It Cost to Repipe a House, Bob Vila, updated April 24, 2023
- Cost to Hire a Plumber, Fixr, updated January 30, 2025
- City of Riverside, work exempt from building permits
- Riverside Public Utilities 2025 Water Quality Report
- Contractors State License Board
Page updated