A dripping shower faucet almost always traces back to a worn washer, O-ring, cartridge or valve seat. The repair goes like this: shut the water off, remove the handle and trim, pull the worn part, match it, fit the new one, then reassemble and test. Single-handle cartridge valves are the easiest, and two-handle compression valves take washers and sometimes a new seat. For other fixture help, see the garbage disposal and fixture plumbers page.
Why does my shower faucet drip?
Dripping from the spout while the shower is off shows the valve is failing to seal: a worn cartridge or stem, hardened washers, a corroded valve seat or a damaged O-ring. Constant pressure on soft rubber, plus mineral scale, causes the wear. A drip from the showerhead only is usually a separate problem, since water trapped in the head may drip briefly.
Hard water can speed this up. Its 2025 report from Riverside Public Utilities gives average hardness of 197 mg/L, about 12 grains per gallon, and scale roughens seats and clogs small passages. A drip on the hot side alone implicates the hot-side washer or the cartridge's hot port. On average, the EPA reports, a household loses over 9,300 gallons of water yearly to leaks.
What if the faucet still drips after I replace the part?
Check three things: that the part is the right one for the valve, that the seat is not damaged, and that the stop or main shutoff is not leaking past. A new washer on a pitted seat still drips. A cartridge not fully seated, or installed with the hot and cold orientation reversed, will leak or give the wrong temperature.
If the water is still leaking behind the wall, you may see staining on the ceiling or wall nearby. Do not keep the water on. A leak inside the wall needs a plumber, and the leak detection and burst pipe guide lists the warning signs.
What kind of shower valve do I have?
Start with the handle. One handle that moves left and right for temperature and in or out for flow is a single-handle valve, usually a cartridge or ball type. Two handles, one hot and one cold, with a turning stem, is a compression or cartridge valve for each side. Behind the trim plate, brand and model marks help.
Brand matters for parts. The cartridge for one maker does not fit another. If you cannot identify the valve, take the old cartridge to a plumbing supply store or look up the model number on the trim. A shower with a diverter for the tub and shower has another part that can leak, which sits in the spout or in a separate handle.
What is the fix for a two-handle shower that leaks?
Turn off the water, take off the handle and trim, then unscrew the stem from the valve body with a socket or wrench. Install exact-match replacements for the rubber washer on the stem's bottom and for the O-ring. Should the brass seat within the valve feel rough, a seat wrench or dresser tool can smooth or replace it. Reassemble and test.
A seat that is worn deeper than a tool can fix means a valve replacement, which usually involves opening the wall or access panel behind the tub. That is the point at which many people hand it off. Corroded stems that will not turn should not be forced, since a break inside the wall turns a cheap fix into a large one.
What is the fix for a single-handle shower that leaks?
Shut the water off at the main or at a local shutoff, open a tap to relieve pressure, and cover the drain. Take out the handle screw, then the handle and trim plate. Release the retaining clip or screws, draw the old cartridge straight out with pliers or a puller, and seat the matching new cartridge facing the same way. Reassemble and test.
Coat the new O-rings in plumber's silicone grease rather than any petroleum product. If the new cartridge still leaks, the valve body seat may be scored or the cartridge may be the wrong one. Bring the water back gradually and look for leaks at the trim before refitting the handle. Keep the old part to compare, and take photos as you go.
At what point should I hire a plumber?
Get help if the shutoff will not close, the stem or cartridge is seized, the valve body has cracked, the leak is behind the wall, or the fix means cutting into tile or drywall. Faucet repair or replacement is on the City of Riverside list of work exempt from permits, but replacing piping behind the face of a wall requires a permit, according to the city's handout.
To have it done properly the first time, request a visit with the quote form. Visits are arranged on weekdays, 9am until 5pm. The Delta-specific steps are in the Delta shower faucet guide, and the faucet installation cost page helps when replacing is the better route.
Common questions
How much water is lost to a dripping shower faucet?
Do I need special tools to fix a shower faucet?
Why does my shower faucet drip after I turn it off?
Is it possible to repair a shower faucet without shutting off the house water?
This guide is one of many on plumber riverside.
Sources used
Page updated