Shut the water off to the tub, find out whether you have one handle or two, and take the handle off. A single-handle tub faucet usually has a cartridge that you pull and replace. A two-handle faucet has a stem with a washer and seat for each side. Match the part, and most drips stop. Stop and call if the handle is stuck or the drip is behind the wall. The faucet, sink, shower and disposal help hub covers related repairs.
Why does my bathtub faucet drip?
The seal inside the faucet has worn out. In a compression faucet that is a rubber washer pressed on a seat. In a cartridge or ball faucet it is the O-rings or the cartridge itself. Wear speeds up when mineral scale roughens the seat. If the spout drips while the faucet is off, the valve is not sealing.
Read the drip's location. Water from the spout when off is a valve seal problem. Water around the handle is an O-ring or packing. Water in the wall or from the ceiling below is a pipe or connection problem, not a faucet issue. A dripping faucet wastes water: the EPA reports that the average household wastes over 9,300 gallons a year to leaks. Hard water makes seals wear faster. Riverside Public Utilities' 2025 report lists hardness averaging 197 mg/L, about 12 grains per gallon.
What kind of tub faucet do I have?
Two handles, one for hot and one for cold, usually means compression stems. One handle that turns for temperature and pulls or pushes for flow is usually a cartridge. A handle that pivots on a ball is a ball-type, more common on kitchen faucets. Pull off the handle cap and look at the parts to be sure.
Brand matters for the part, not the method. Moen and Delta, for example, sell cartridges that are not interchangeable, and each brand and model line has its own part number. Take the old cartridge to a hardware store or search the model number stamped on the valve. The brand-specific guide for a common case is fixing a leaky Delta shower faucet.
What are the steps to repair a dripping tub faucet?
Turn off the water at the shutoff for the bathroom or at the main, run the faucet to empty the lines, plug the tub drain, remove the handle and trim, and pull the cartridge or stem. Replace the washer, O-rings or cartridge with exact matches, reassemble, and turn the water on slowly.
Steps:
- Turn the water off. If there is no bathroom shutoff, use the main valve, and test by opening the faucet.
- Plug the drain so screws do not fall in. Lay a towel in the tub.
- Lever off the handle cap, take out the screw and draw off the handle.
- Take off the escutcheon plate, then the bonnet nut or retaining clip.
- Either draw out the cartridge or unscrew the stem, and note which way it faces.
- Inspect the seat in a compression valve. If it is rough, a seat wrench or a dressing tool can smooth it, or the seat can be replaced.
- Install the new parts, replace the clip, and reassemble.
- Turn on the water slowly, check for leaks at the handle and spout, and test hot and cold.
If a cartridge is stuck from scale, a cartridge puller helps, and forcing it can crack the valve body. Damage to the valve body may mean opening the wall, which is work for a plumber.
What about a faucet that leaks from the handle or the spout?
A leak from the handle means a worn O-ring or a loose packing nut: tighten gently or replace. A leak from the spout when on is normal, and when off is the valve. A spout that drips from the diverter, or a shower head that dribbles after you switch to the tub, means the diverter is worn.
Models with one handle or two are covered by leaky faucet repair for two handles and leaky tub faucet repair. If the shower head is the one that drips, read repairing a dripping shower faucet and plumber for shower leaks.
When does a plumber need to fix it?
Call a plumber when the handle or trim stays stuck, when the valve body is cracked or corroded, when the leak sits behind the wall, or when there is no shutoff and the main will not close. Also call when you have replaced the parts and the drip returns, because the problem may be the seat or the valve.
The City of Riverside's work-exempt handout lists faucet repair and replacement as exempt from permits, but replacing piping behind the wall requires a permit. Ask about it if the wall has to be opened by the plumber. California requires a contractor license for jobs of $1,000 or more in labor and materials, so check at cslb.ca.gov for bigger work.
Fixr's bathroom sink guide, updated January 30, 2025, lists installed bathroom sink faucets from $225 to $1,350 depending on type, which gives a rough sense of replacement versus repair, though it does not price tub valves. These are national guide figures, not Riverside rates and not what we charge. See faucet replacement cost and the faucet install cost page.
Older homes can have old tub valves behind tile, and replacing one may mean opening the wall. A plumber can tell which kind you have.
When to call a plumber business
Call when you have worked through the steps and the leak persists, when water stains show on the ceiling below, or when you would rather hand it off. We pass your request to a local plumbing business that visits, and a written quote reaches you before work starts. Take a photo of the faucet and the handle, and note the brand if you can.
Back to Rubidoux Ridge Plumbing for all services.
Common questions
How much time does a leaky tub faucet repair take?
Which questions do I put to a plumber for a leaky faucet?
Who needs to be home for the plumber's visit?
Do I need to turn off the main water?
What if the faucet still drips following a cartridge replacement?
Sources used
Page updated