Jump to content
Call us (951) 749-6477

Guide ยท Riverside

Garbage disposal installation service in Riverside

Installing a disposal takes a sink flange, a mounting ring, a drain connection and a power source. This page covers what a plumber does, what it costs by guide figures, and what to ask.

Disposal cutaway under the sink showing the flange, dishwasher inlet, drain to the trap, and power.

A disposal install replaces or adds a grinding unit under the kitchen sink drain. The plumber mounts the unit to the sink flange, connects the drain and dishwasher hose, and wires or plugs in the power. Fixr's 2025 guide lists $300 to $600 for the job, about $500 on average. If your disposal is acting up and may only need repair, start with garbage disposal repair. The full list of services is at Rubidoux Ridge Plumbing.

What steps go into installing a garbage disposal?

The plumber removes the old unit if there is one, cleans the sink flange, sets the new mounting assembly, hangs the disposal, connects the discharge pipe to the trap, attaches the dishwasher drain hose if you have one, then hooks up power and checks for leaks and noise. A new installation where none existed adds an electrical outlet and a switch.

The standard sequence:

  1. Power and water off, and the old unit disconnected.
  2. The old flange and ring removed, and putty or a gasket set for the new one.
  3. The new mounting assembly tightened under the sink.
  4. The unit hung, the discharge elbow connected and the trap reconnected.
  5. The dishwasher knockout punched out if a dishwasher drain will connect, which is an easy step to miss.
  6. Power connected, and the test run with water.

The knockout is a small plug inside the inlet. If it is left in, the dishwasher cannot drain and backs up into the sink. It is an easy step to miss, and a plumber will ask about it. See fixing the kitchen sink faucet if you are doing other sink work at the same time.

What is the price of putting in a garbage disposal?

Fixr's "Garbage Disposal Installation Cost" guide, updated January 31, 2025, lists $300 to $600, average $500, with plumber labor about $300 of that. These are national guide figures, not Riverside rates and not what we charge. Fixr's plumber guide lists typical hourly labor at $75 to $150 with service call fees of $50 to $300. The written quote sets the price.

What changes the number: the unit's horsepower and quality, whether you have a power source and a switch, whether a dishwasher hookup is needed, any plumbing changes to a bad trap or drain, and disposal of the old unit. A job that needs a new circuit or a switch adds an electrician, and in some homes that is more than the unit.

No second guide with a readable range turned up, so a different range is not quoted here. See also the cost of faucet replacement for sink work done at the same time.

Does a disposal need an electrical outlet?

Yes. A disposal needs power, either a hardwired connection or a plug in an outlet beneath the sink, depending on the model and how the sink was set up. If the sink has no switch or outlet, someone has to add one, and electrical work is not plumbing. An existing outlet may be usable by the plumber.

Two ways a disposal gets power: a plug-in outlet under the sink, or hardwiring through a wall switch.

If you are replacing an old unit, the power is likely in place. Ask the plumber whether the existing cord and switch work with the new unit, or whether a cord kit is needed. If you are adding the first disposal in the kitchen, plan for the electrical step, and check if the quote covers it or if a separate electrician is needed. Wiring is regulated work, and jobs of $1,000 or more require a contractor license.

Can I install a disposal myself?

Many homeowners replace a like-for-like unit, but it takes time and a few tools, and you are working under the sink with wiring. Adding a unit where the sink never had one changes the drain, the knockout and the wiring. The risk is a leak below the sink. If you are unsure, hire a plumber.

Riverside's work-exempt handout lists faucet and toilet repair and replacement as exempt from permits, and does not mention disposals. Replacing piping inside the wall or beneath the floor requires a permit, so if the install moves drain pipe, ask Riverside Building and Safety at (951) 826-5800. Moreno Valley and Loma Linda have their own divisions.

For help with leaks after an install, see repairing a leaking pipe under the sink.

What should I look for in a disposal?

Horsepower, feed type and noise are the main differences. Continuous-feed units are common and run while you add scraps. Batch-feed units run when you lock the stopper in place. A larger motor grinds more and jams less. Insulation reduces noise. Check what the grinding parts are made of, since makers describe their materials differently.

Hard water affects fixtures: Riverside Public Utilities' 2025 report lists hardness averaging 197 mg/L, about 12 grains per gallon, and sink traps collect mineral buildup. A disposal does not need special treatment for that, but keep the drain flowing with cold water. Our unclogging guide covers the usual clog.

When to call a plumber business

Call when you want a disposal installed or replaced, when the old one is leaking from the body, when you need a switch or outlet added, or when the sink drain is in poor shape. We pass your request to a local plumbing business that visits, and a written quote reaches you before work starts. Have the sink type and a photo of the cabinet ready.

Jobs of $1,000 or more in labor and materials need a California contractor license, which you can look up by number on the CSLB site, cslb.ca.gov.

Book a plumber quote

Tell us about the job. We'll arrange a visit and a written quote before any work starts.

Lets the business see where the job is before they quote.

We earn a referral fee from the plumber who gets your job. You pay us nothing.

Common questions

How long does a disposal installation take?

A like-for-like swap is usually a short visit, while a first-ever install that adds a switch or outlet takes longer, since the electrical step may need a second trade. The estimate belongs in the written quote, and it is worth asking if the old unit leaves the same day.

Which questions should I put to an installer before hiring?

Find out if the price covers the unit, the power connection, the dishwasher hookup, removal of the old unit and any trap repair. Get the contractor license number and verify it at cslb.ca.gov, and learn what extra is charged if the sink needs other repairs.

Who should be home during the install?

Someone over 18 needs to be home to open up the kitchen and the sink cabinet, and to approve the finished work. Water to the sink is shut off for part of the visit. When you are away, ask if a different adult can let the plumber in.

Do I have to buy the disposal myself?

It depends on the quote. Some plumbers supply the unit and some install one you bought. Ask which is better value. If you supply it, make sure it matches the sink flange and the power setup, and check with the plumber if the labor price shifts when the unit is not the one they would have picked.

What if my dishwasher backs up after the install?

Check that the knockout plug was removed from the inlet, and that the dishwasher hose is looped high or has an air gap. A plumber can fix that quickly. If water backs up into the sink every time the dishwasher drains, tell the plumber about it right away and do not keep running the machine.

Sources used

Page updated