A Navien tankless that quits heating will normally flash a code starting with E, and that code is the best lead you have, since it narrows the fault before a cover comes off. This page is part of the water heater repair guide. It focuses on one popular tankless brand. To have a local plumber inspect a unit, use the form on the home page.
How should I read a Navien error code?
Navien displays a numbered code when a sensor or safety circuit reports a problem. The NPE-180A manual lists E003 as an ignition failure, E012 as flame loss, E016 as an overheated heat exchanger and E109 as an abnormal fan motor. Codes vary between models, so compare yours with the manual that shipped with the unit.
Record the code, the model number printed on the side label, and whether trouble started after a power cut, a gas interruption or heavy use. That alone often points a plumber to the right spot. Snap a photo of the display before resetting, because some codes disappear on restart and return later.
Why does my Navien show E003 or fail to ignite?
E003 says the burner attempted to light and failed. The manual's list starts with making sure the main gas supply valve is open. Other sensible checks are power at the unit and a sound ground connection. Possible culprits include a shut valve, an interrupted gas supply, or an igniter or flame sensor that has worn out or needs cleaning.
Begin with what is visible. The gas shutoff handle should sit parallel to its pipe. If a gas range or furnace is also dead, the trouble lies upstream of the heater. SoCalGas serves Riverside, Moreno Valley and Loma Linda. If you smell gas, stop everything: everyone walks out, you ring SoCalGas at 1-800-427-2200 from a safe distance, and 911 is called if anyone is at risk. Burner and gas pipe work belongs to a contractor; California requires a license for jobs of $1,000 or above, or whenever a permit applies.
What causes flame loss or the E012 code?
Flame loss describes a burner that lit, then died. Possible reasons: a grimy flame rod, starved combustion air or a blocked intake, a weak ground, or gas pressure that sags when other appliances fire up. The flame rod and the intake air path are sensible places for a plumber to start, though the manual page should be checked for your model.
Intake and exhaust venting matter on a tankless unit because it burns a large amount of fuel at once. Look for a nest, a vent joint that has come apart, or a dented intake pipe, and keep stored items away from the unit. Leave the combustion chamber closed. Plumbers carry the instruments to read gas pressure and test combustion, and recurring flame loss justifies a visit rather than another reset.
Why does it overheat, and does hard water matter?
E016 refers to an overheated heat exchanger, and a common cause is mineral scale inside it. Scale acts like insulation, so the metal runs hot while the water flowing through it picks up less heat. Riverside Public Utilities' 2025 report lists hardness averaging 197 mg/L, about 12 grains per gallon, so scale is a realistic concern for tankless owners here.
The standard cure is a descaling flush, in which a small pump circulates a mild acid cleaner, commonly white vinegar or a solution made for descaling, through the heat exchanger by way of the service valves. Valves added at installation make that simple, so find out whether yours has them. Check your Navien manual for its recommended maintenance schedule, since we do not repeat a number that varies by model. Ways to slow the buildup are in scale prevention.
What about a fan or venting fault such as E109?
E109 involves the combustion fan. Check that the vent and air intake are open first. If the code persists, the fan motor or the control board could be failing, a job for a plumber or a technician trained on the brand. The manual directs unresolved codes to Navien technical support.
A noisy fan, a rattle or a burning smell are reasons to switch the unit off and call. Parts availability can differ by model and age. Have the plumber verify the part number against the label before approving, and set the quote beside a replacement price if the unit is aging. See our tankless repair overview for other brands and general faults.
When is repair not worth it?
Repair suits a bad sensor, igniter or fan, or a scale flush. Replacement can come out ahead when an older unit's heat exchanger has failed, when faults keep coming back, or when parts are discontinued. Request prices for both in the written quote. For new installs, see Navien tankless installation.
If it comes to replacement, a permit is likely needed, so check with your city; City of Riverside Building and Safety answers at (951) 826-5800. Gas and vent changes go to a contractor. No repair price is printed here, as no verified guide figure for Navien repairs turned up, and the total depends on the part and labor.
Common questions
How do I reset a Navien tankless water heater?
Why does my Navien give hot water, then cold?
How long does a Navien repair take?
Which questions should I put to a plumber about my Navien?
Can I fix a Navien tankless heater myself?
Sources used
Page updated