Jump to content
Call us (951) 749-6477

Guide ยท Riverside

Navien tankless water heater installation in Riverside

Installing a Navien tankless heater is more than swapping boxes. Gas supply, venting, a condensate drain and the water connections all have to suit the unit. Here is the job laid out so you can read a quote.

Wall section with a concentric vent: inner exhaust pipe inside an outer air pipe, running through the wall.

Five pieces make up a Navien tankless install: the wall-mounted unit, a gas line sized for it, a vent path outdoors, a drain for the condensate it produces, and the water and electrical connections. The plumber maps out all five prior to removing the old heater. We pass your request to a local plumbing business, and the water heater repair page walks through the quote process. Request a quote whenever you are ready.

What steps does a Navien tankless installation include?

First the old water heater comes out, then the Navien unit is mounted, gas and water are connected with isolation valves, the vent and condensate drain are run, power is wired or plugged in, and the system is filled and tested. Details vary by model and site, so the plumber follows the maker's installation manual.

Many tankless models are condensing units that pull extra heat from the exhaust and create acidic condensate, which must drain safely. Your model's manual tells you which type you have. A condensing unit needs a drain close by or a neutralizer, and plastic vent pipe is typical for them.

Isolation valves on the water side allow the unit to be flushed and descaled later, which counts in hard water. Public figures for the area are available: the Riverside Public Utilities 2025 report shows average hardness of 197 mg/L (roughly 12 grains per gallon), and the EMWD 2025 report shows Mills-area hardness averaging 5.1 to 7.5 grains per gallon. A plumber who fits those valves spares you a later visit.

Can my current gas line serve a tankless heater?

Frequently not without changes. When it fires, a tankless unit uses gas far faster than a tank heater, so the line has to be sized to supply it. The plumber compares pipe diameter, length and the meter's capacity with the unit's rating, and a larger line may be required.

Gas meter feeding a main line, with a branch and shutoff to the tankless heater.

Here the Navien manual and the plumber's calculation outweigh rules of thumb. SoCalGas supplies gas to Riverside, Moreno Valley and Loma Linda, and a larger load may be something it needs to hear about for your meter. The plumber can ask.

Gas work is regulated and requires a permit, so do-it-yourself ends here. Smelling gas at any moment means leaving the building and phoning SoCalGas on 1-800-427-2200 from outside. The page on gas plumber work covers the gas side, and gas tankless installation describes the general job.

How does venting limit where the unit can go?

Venting varies by model. Certain units vent through a wall, others through a roof, and some can sit outdoors. The plumber measures the run and counts elbows, since the manual caps length and turns. Clearances from windows, doors and meters apply as well, and a poor location can rule out a model.

Indoors, the best spot is often beside the current water heater so piping can be reused, though a garage, a closet and an exterior wall each follow different rules. More recent houses in Orangecrest and east Moreno Valley may offer an easier path than older ones in Downtown Riverside or the Wood Streets, where wall or attic space can be tight.

An outdoor setup skips long vents but leaves the unit and its pipes exposed to weather, so the plumber plans protection for both. The options get weighed with you, and tankless water heater installation has more on the choices.

How much does a Navien tankless installation cost?

Fixr (updated January 31, 2025) gives $2,500 to $4,500 for a typical tankless installation, and This Old House (updated June 17, 2026) gives $2,100 to $4,000 installed. Both are national guide figures, not local rates and not what we charge. The written quote sets the price.

Gas line work, the vent, the unit size and the wall it mounts on drive the spread. A job needing a new gas line, a new roof vent and a condensate drain costs more than replacing a unit with one of the same type in the same place. No Navien-specific figure came from a source we could read, so none is quoted.

Request a quote that puts the unit, gas piping, venting, drain, valves, permit and old-heater removal on separate lines. The bigger picture is in tankless water heater cost of installation and water heater replacement cost.

Is a permit required, and who is allowed to install it?

A water heater swap in Riverside generally needs a permit, so call Building and Safety at (951) 826-5800. Moreno Valley's division is at (951) 413-3350 and Loma Linda's permit line is (909) 799-2836. Each city's water heater rule could not be confirmed, so ask the office covering your address.

The Contractors State License Board states that a California contractor license is needed for jobs reaching $1,000 in labor and materials, or any job requiring a permit. A tankless install passes that mark. Look up the plumber's license on the board's site, and ask who pulls the permit and books the inspection.

Faucet and toilet replacement appear on the City of Riverside's exempt-work list, but water heaters do not. Treat a tankless install as permitted work.

Does a Navien tankless beat a tank heater?

Neither wins in every case. Tankless units supply continuous hot water and take less room, yet they cost more up front and depend on good gas, venting and descaling. A tank is simpler and cheaper to put in. The tank versus tankless guide sets them side by side.

Household size counts. A large family running a dishwasher alongside two showers needs a unit sized for that flow, which the plumber calculates from fixtures and incoming water temperature. A small household often needs less capacity. Have the plumber show the numbers.

Already own a Navien that misbehaves? The troubleshooting side is in Navien tankless repair. Other makes are handled in Rinnai installation and Rheem tankless repair.

Requests we pass along cover Riverside, Moreno Valley and Loma Linda. The home page lists the other services.

Common questions

What is the usual length of a Navien tankless installation?

Replacing a unit with one of the same type in the same place is the simplest version. A job adding a gas line, a new vent route or an electrical circuit can run longer, and a permit inspection adds a visit. The written quote should carry a time estimate from the plumber.

Which questions should I ask before choosing an installer?

Check whether the gas line is large enough, how the unit will vent, where the condensate drains, who pulls the permit, whether isolation valves come with it and what the quote covers. Request the plumber's California contractor license number and verify it on the Contractors State License Board site.

Does a tankless heater need maintenance?

Yes. Descaling and cleaning the inlet screen matter, particularly in hard water, and the maker's manual sets the schedule. Isolation valves fitted with the unit speed up that upkeep. Skipping it can shorten the heat exchanger's life, so have the plumber record the first service date in the paperwork.

Can I install a Navien tankless heater myself?

We advise against it. The work involves gas piping, venting and usually a permit, and permitted work in California requires a contractor license. A mistake risks gas leaks and carbon monoxide. Put your effort into choosing the model and reviewing the written quote.

Sources used

Page updated