Installing a tankless hot water heater is a bigger job than swapping a tank. The unit mounts on a wall, needs a vent rated for the model, and either a gas line or an electrical circuit sized for the surge of power it draws. Plan for a plumber visit and a permit, and ask how long the job will run. Our water heater page covers repairs and replacements in general.
Which steps make up a tankless installation?
The plumber removes the old tank if there is one, mounts the new unit, connects cold and hot water with isolation valves, runs the gas line and vent or the electrical feed, adds a condensate drain if the model is a condensing one, and tests everything. You also get an inspection under a permit, plus a brief walkthrough of the controls.
Compared with a tank, three things are new. First, gas demand is higher while the unit fires, so the existing gas pipe may need to be enlarged. Second, the flue is specific to the model. Third, the isolation valves matter, because the unit needs periodic flushing. If the quote does not mention the vent and gas pipe, ask why.
SoCalGas serves Riverside, Moreno Valley and Loma Linda, and a gas tankless installation typically means a gas line review. The page on gas line plumbing shows how that work is handled.
Do condensing tankless models need a different install?
A condensing tankless heater pulls extra heat out of its exhaust, so the exhaust runs cooler and the unit more efficiently. That means plastic vent pipe is often used and the exhaust makes acidic condensate that must drain somewhere. The installer needs a floor drain, a condensate neutralizer or a safe path for it.
Practical differences you will see in a quote: PVC or CPVC venting rather than metal, a condensate line with a small neutralizer cartridge in some cases, and an electrical outlet nearby since the unit has a fan and electronics. A non-condensing model vents through a metal pipe and is simpler to place, but wastes more heat.
Brands such as Rinnai and Navien publish manuals with minimum clearances and vent lengths. The plumber follows that manual, not a general rule. For brand specifics read the pages on Rinnai installation and Navien installation.
What does a natural gas tankless install need?
A natural gas unit needs a gas line large enough to feed the burner at full fire, a shutoff valve and a sediment trap or drip leg at the appliance, a vent to the outdoors and a combustion air path. The plumber calculates the gas load for every appliance on the line, not just the new heater.
If the existing pipe is undersized, expect a larger line from the meter or the nearest branch, which adds cost. A pressure test follows. Gas piping work needs a permit, and in California only a contractor with a license may do it. Do not attempt a gas connection yourself.
Whenever you smell gas, get out of the building, then phone SoCalGas on 1-800-427-2200 from a safe spot outside, or dial 911 when you are in danger. See gas tankless installation for more on the gas side.
What are the code and permit requirements for water heater installation?
Replacing a water heater in Riverside usually requires a permit, so confirm with City Building and Safety on (951) 826-5800. Moreno Valley's Building and Safety line is (951) 413-3350, and the city says the 2025 California codes took effect January 1, 2026. We did not verify a specific water heater permit rule for Moreno Valley or Loma Linda.
Past the permit, installers follow the California Plumbing Code along with the manufacturer's installation manual. Inspectors commonly look at vent material and slope, gas pipe sizing, combustion air, the temperature and pressure relief valve with a proper discharge pipe, and a shutoff within reach. An expansion tank is often needed on a closed system.
In June 2025 the regional air board voted against amending Rules 1111 and 1121, so that rulemaking changes nothing about what you can install today. Ask the plumber and the city which models are allowed when your permit is issued.
How much does a tankless install cost?
Guides put tankless installation at roughly $2,100 to $4,000 (This Old House, updated June 17, 2026) and $2,500 to $4,500 for a typical job (Fixr, updated January 31, 2025). Fixr lists gas installs at $1,400 to $3,500 and electric at $1,000 to $3,000. Those are national guide figures, not local rates. The written quote sets the price.
Costs climb with a new gas line, a long vent run, a wall needing reinforcement, a condensate drain, and permit fees. They fall when the old heater sat in the same spot with a nearby vent. For the full comparison, open what tankless installation costs and the page on replacing a water heater.
Is a tankless the right choice for my home?
It depends on hot water habits and the house. A tankless unit gives an endless supply for a long shower and saves the standby heat a tank loses, but it costs more upfront, needs gas and vent work, and can run cold-water sandwiches in low-flow use. A tank heater costs less and is simpler to install.
For older homes in the Wood Streets, Arlington or Eastside, the gas line and vent path can be the deciding factor. Newer homes in Orangecrest and east Moreno Valley may already have a vent chase that suits a wall-hung unit. Compare options on tank versus tankless. Hard water matters too: scale shortens the life of the heat exchanger, so pair the unit with a plan for flushing or a softener; see hard water scale prevention.
What if the taps are hot but the house is cold, or nothing is hot?
In a typical American home, hot water and space heating run on separate equipment. If your tap water is hot but the house is cold, the furnace or its thermostat is the issue, and a heating and air business should take it. A combination boiler can link the two, so ask the plumber what you have.
If a tankless unit shows an error code, no hot water, or cold-water pockets, check the gas valve is open, the power is on, the vent is clear and the filter screens are clean. Then see no hot water for the main causes. A heater that repeats an error needs a plumber.
When to call a plumber business
Call before you buy, if you can. A visit settles the gas size, the vent route and the permit, and prevents buying a model that does not fit. Call right away if you smell gas, see soot at the unit, or the heater leaks.
Hand over what you know: the make and model of the old heater, where it sits, the gas meter location, and photos. Then request a quote and we pass the job to a local plumbing business. Professional installation matters here because a faulty vent or gas connection is a safety issue, not just a nuisance. Start at the home page for other jobs.
Common questions
How many hours does a tankless installation need?
What should I settle before hiring a tankless installer?
Is an adult needed at home during installation?
Will my old vent work with a new tankless heater?
Sources used
- This Old House, How Much Does Water Heater Installation Cost? (2026), updated June 17, 2026
- Fixr, Tankless Water Heater Installation Cost, updated January 31, 2025
- City of Riverside Building and Safety, contact
- City of Moreno Valley Building and Safety
- SoCalGas cities served list
- California Contractors State License Board
Page updated