Jump to content
Call us (951) 749-6477

Guide ยท Riverside

Tankless water heater cost of installation in Riverside

Guides put a typical tankless installation between $2,100 and $4,500, with gas models needing more pipe and venting work than electric ones. Here is how the pieces add up in an Inland Empire house.

Wall-mounted tankless water heater with gas supply, cold water in, hot water out and a sealed vent

Installing a tankless water heater costs about $2,500 to $4,500 for a typical job, with an average near $2,811, according to Fixr's guide updated January 31, 2025. This Old House's 2026 guide gives $2,100 to $4,000 installed. National guide figures, not Riverside rates and not what we charge, and the written quote sets the price. For repair and replacement in general, see our water heater page, and for the rest of our coverage visit the home page.

How much should I pay a plumber to install a water heater?

For a tankless unit, the guides above put the all-in figure at roughly $2,100 to $4,500. For a standard tank, This Old House lists $1,200 to $2,300 and Fixr lists $800 to $1,500 for electric and $1,000 to $2,700 for gas. Whether a quote is fair depends on what it covers, and you should compare scope line by line before comparing totals.

Ask the plumber to separate the unit, labor, venting, gas line or electrical work, permit, a shutoff or isolation valve set, and removal of the old tank. A bargain price that omits the vent or the electrical panel upgrade is not a bargain. For the tank side of the same math, see what a water heater replacement costs.

What does the unit cost and what does labor cost?

Fixr's tankless guide splits labor out: electric models run $1,000 to $3,000 installed with labor of $500 to $1,000, and gas models run $1,400 to $3,500 installed with labor of $900 to $1,500. The gas figures run higher in that guide. A gas unit usually adds venting and gas piping, whereas an electric unit can call for a heavier circuit.

Two installed price bars on one dollar scale: electric 1,000 to 3,000, gas 1,400 to 3,500

That page also gives other sets of figures, so we use only its typical range. Labor is where a house's quirks show up. A tankless unit hung on the garage wall where the old tank stood is simple. A move to an exterior wall, a long gas run, or a panel upgrade adds hours. Hourly rates for labor are covered in what a plumber charges per hour.

Why does a gas tankless cost more in an older house?

A tankless gas unit pulls much more gas in one go than a tank burner does, so the existing pipe may be undersized, and the exhaust needs sealed venting out through a wall or the roof. Riverside homes from the orange-grove era and mid-century Eastside bungalows may have a gas line built for a tank heater plus a furnace, not for a high-input unit.

SoCalGas serves Riverside, Moreno Valley and Loma Linda, per its cities list, and whoever handles the gas work sizes the line for the unit's input rating. Permits are normally needed for gas piping, so check with the city. Our pages on gas tankless water heater installation and residential gas piping codes go further. Brand pages exist for Navien and Rinnai.

What about electric tankless water heaters?

Electric tankless units are smaller and need no venting, yet they draw a heavy electrical load, often requiring their own high-amperage circuit and sometimes a bigger panel. That is why the Fixr figures show electric at $1,000 to $3,000 installed, with the electrical work varying the most between homes.

In a house with an older 100-amp panel, ask the plumber or an electrician whether the load fits. The work may need an electrician on the job in addition to the plumber, and the quote should say who handles which part. A newer home may have more room in the panel, but check rather than assume.

How much do smaller water heater jobs cost?

No sourced price is available to us for anode rod replacement, a gas valve, a water valve, a heating element, or a 40-gallon tank swap on its own. For a 50-gallon electric tank swap, Fixr's 2026 guide lists $800 to $1,500 installed for electric tank-style units overall. Fixr's plumber guide gives hourly rates and a service call fee, which cover a small repair visit.

On that page, typical plumber rates run $75 to $150 per hour, with a service call fee of $50 to $300. When you call, find out if the visit has a call-out fee and if that fee is credited against the job. For common small parts, see anode rod replacement, relief valve replacement and replacement elements.

Book a plumber quote

Tell us about the job. We'll arrange a visit and a written quote before any work starts.

Lets the business see where the job is before they quote.

We earn a referral fee from the plumber who gets your job. You pay us nothing.

Does the higher installation price of a tankless heater pay off?

It can be, for a household that values endless hot water and floor space, but the extra up-front cost may take a long time to recover through energy savings alone. Guides show tankless costing more installed than tank units in the same fuel class. Whether it saves money depends on gas prices, use, and the house.

Read the comparison in tankless gas water heater vs tank and the longer tank versus tankless guide. Hard water raises one more cost: scale builds up in a tankless heat exchanger, and Riverside Public Utilities' 2025 report lists hardness averaging 197 mg/L, about 12 grains per gallon, so check the maker's manual for its descaling advice, which is part of the ownership cost.

Common questions

What is the time needed to install a tankless water heater?

How long it takes depends on the house. A job that adds venting, a gas line or a bigger panel takes longer than replacing one unit with its equal, and we have no sourced figure for either. The plumber business that takes your request gives its own timing in the written quote. A permit job also needs an inspection, which sets the final date.

Which questions should go to an installer of a tankless unit?

Ask which model, what its gas or electrical input is, whether the gas line or panel needs work, who is responsible for the permit, what the venting plan is, and the contractor license number so you can check cslb.ca.gov. Have the quote show the unit, labor, permit and old-unit removal as separate lines.

Does someone have to be home while it is installed?

Yes. An adult needs to open the door, approve any change, and take a walkthrough at the end. Hot water is shut off through the swap, and gas or power to the heater is off for part of the day. Clear the area around the old tank before the visit.

Can a tankless heater replace my tank without upgrading anything else?

Sometimes, but plan on at least a new vent and often a larger gas line or a bigger electrical circuit. Whether your house needs more depends on the unit's input and what the building already has. The plumber should check the gas meter capacity, the pipe size and the panel before quoting, not after starting.

Does a permit apply to a tankless installation?

Likely yes, but confirm with your city. Replacement or conversion of a regulated plumbing, gas or electrical system requires a permit within the City of Riverside, according to its permit documents, and the Building and Safety counter is at (951) 826-5800. For Moreno Valley, call (951) 413-3350, and for Loma Linda, (909) 799-2836. The plumber business usually handles the permit.

Sources used

Page updated