Rheem makes gas and electric tankless heaters, and the faults on them follow a pattern: the display shows a code, the water turns lukewarm, the unit short cycles, or nothing happens at all. Many of these trace to scale, a blocked filter or a gas or venting issue. Check the basics below, then request a quote and we'll arrange a local plumber to come to you. Our wider water heater repair page covers tanks and other brands.
Why is my Rheem tankless water heater not heating?
The common causes are no power, no gas, a closed gas or water valve, a clogged inlet filter, scale built up in the heat exchanger, a venting problem or a sensor fault. Make sure the unit is getting power and the gas and water shutoffs are open. If the display shows a code, look it up in the Rheem manual for your model.
Flow matters. A tankless unit lights only when it sees enough water moving, so a partly open valve or a clogged aerator can keep it from firing. Try a different tap. If hot water works at one fixture and not another, the problem is in that fixture or its line, not the heater.
If a unit has never worked right since installation, the cause is often how it was set up: undersized gas line, wrong venting or crossed hot and cold connections. A plumber can check those. Our guide to gas tankless installation lists what a correct setup includes.
What do the error codes mean?
Rheem displays codes that point to ignition, flow, temperature, venting or sensor faults, and the list differs by model. We do not list codes here because they vary by series and year. Look at the model number on the data plate and use the manual or the maker's support site, then tell the plumber the code.
Record the code exactly as shown, plus what the unit was doing when it appeared. A code that clears when you reset the unit and returns within a day suggests a developing fault. Constant codes after a reset are a sign to stop resetting and call.
Do not take panels off a gas unit with the gas on. Should you smell gas, get out of the house and phone SoCalGas on 1-800-427-2200 when you are outside. SoCalGas says to leave the gas off until the utility restores it.
Can scale cause a Rheem tankless water heater to fail?
Yes. Minerals from hard water coat the heat exchanger and narrow the passages, which cuts flow, raises temperatures and triggers codes. In the Riverside area the figures are public: the 2025 Riverside Public Utilities report lists hardness averaging 197 mg/L (about 12 grains per gallon), and EMWD's 2025 report lists Mills-area hardness averaging 5.1 to 7.5 grains per gallon.
Descaling is the maintenance step: a plumber or a capable owner runs descaling solution around the unit using a small pump and hoses. The method and the interval come from the maker's instructions, and the right schedule is shorter in hard water. Skipping it is a common reason tankless units fail early.
Many tankless heaters have inlet screens that collect debris. Close the shutoff valves, relieve pressure and clean the screen as the manual shows. A clogged screen can cut flow enough that the unit will not fire, and it takes minutes to check.
If your water is softened, scale is less of a problem. For how scale appears around the house, see removing hard water scale.
What about lukewarm water and the cold water sandwich?
Lukewarm water that fluctuates can come from low flow, scale, a mixing valve elsewhere in the system, a crossed connection or a recirculation setup that feeds cold water back into the hot line. The cold water sandwich, a brief slug of cold water between two hot ones, is a feature of tankless heaters, and a plumber can reduce it.
Check whether the problem is at one fixture. A mixing cartridge that has worn out in a shower can cause temperature swings that look like heater trouble. If all taps are affected, the heater or its flow settings deserve a look. Low flow rates can also keep the unit from firing, so a very small trickle may produce cold water.
For similar situations on other makes, see tankless water heater repair. For the hot-water-low-pressure side of the problem, hot water pressure low explains where to look.
What Rheem repairs are fine for a homeowner, and what calls for a plumber?
You can check the power, open the shutoffs, clean the inlet screen, note codes and descale if the manual and your comfort level agree. Leave gas connections, venting, burner or flame sensor work, and anything that opens the gas valve to a plumber. These parts are regulated work, and mistakes risk fire and carbon monoxide.
The Contractors State License Board requires a California contractor license once work needs a permit or reaches $1,000 in labor and materials. In Riverside a replacement water heater usually needs a permit, so confirm with Building and Safety at (951) 826-5800. Repairs of parts may not, and the plumber knows the line.
Respect the electrical side too. A tankless unit may pull heavy current or need its own circuit, and wet floors and live power are a bad combination. Should water pool near the unit, turn the power off at the panel before you go close.
Is it worth repairing a Rheem tankless water heater?
Often yes, because tankless units are built to be serviced part by part, and guides commonly cite a life of around 20 years with maintenance. A repair on a unit that is a few years old makes sense. Replacement may be the wiser choice for an older unit with a cracked heat exchanger or repeated failures.
Ask the plumber to explain the failure, the extent of the repair and the unit's general condition. If you are weighing a swap, our guides to tank versus tankless and tankless installation cost put numbers next to the options. Other makes are covered at Navien tankless repair, Rinnai tankless repair and Noritz tankless repair.
We arrange work in Riverside, Moreno Valley and Loma Linda. The rest of our services are on the home page.
Common questions
How often should a Rheem tankless heater be flushed?
Why does my unit keep turning off by itself?
Do I need a permit to repair or replace one?
Who repairs a Rheem tankless heater in Moreno Valley or Loma Linda?
Sources used
Page updated