Jump to content
Call us (951) 749-6477

Guide ยท Riverside

Rinnai tankless water heater repair: codes, flushing and when to call

Most Rinnai problems announce themselves with a diagnostic code, and the common ones are ignition, flame and scale. This page explains what Rinnai says each means and what a plumber does about it.

Tankless heater layout: cold water into the heat exchanger, gas burner, hot outlet, and vent.

A Rinnai tankless unit heats water on demand and tells you what is wrong through a code on its display. Two codes come up most: 11, where the burner will not light, and 12, where the flame starts and then drops out. A third family, LC0 to LC9, points to scale. Some of these you can clear yourself and some belong to a plumber. This page works from Rinnai's own documents, while other faults sit in the water heater repair hub.

Always check the model number on your unit, since code lists vary by series. Rinnai's manual for your model is the final word.

What does Rinnai error code 11 mean?

Code 11 means no ignition: the heater called for heat but the burner did not light. Rinnai's troubleshooting guide lists closed gas valves, gas not reaching the unit, an empty propane tank, air left in the gas lines, low inlet gas pressure, and a loose sparker or flame rod among the causes.

Start with the easy checks. Make sure the gas is on at the heater and at the meter, and that other gas appliances work. If you have propane, check the tank has fuel. If it still shows 11, a loose electrode, bad connection, failed circuit board, faulty gas valve or low inlet gas pressure are possible, and each of those is plumber or technician work.

A gas smell takes priority over everything on this page. Step outside, dial SoCalGas on 1-800-427-2200, and call 911 should you be in danger.

What does error code 12 mean?

Code 12 is flame failure: the burner lights, then the flame goes out. Rinnai says to verify inlet gas pressure against the rating plate and to check the vent. A vent terminal that does not meet its clearances can recirculate exhaust, which disrupts combustion and brings on a 12. Damage to the flame rod wiring or its silicone sleeve is another cause.

If code 12 appears the instant water starts flowing and no flame is visible, Rinnai points to an electrical short in one of the unit's components. That is not a home fix.

Venting and gas supply are the code-governed side of the job. A plumber used to tankless units checks pressure, vent run and clearances together, so a 12 that will not go away belongs with them. Ask during the visit whether the gas line has the capacity the manual calls for.

What is the LC code, and does the heater need flushing?

An LC code from 0 to 9 signals scale inside the heat exchanger, so the unit wants a flush. Rinnai's flushing page recommends a flush yearly at minimum, and its troubleshooting guide says hard water must be treated to prevent scale damage. On older units the heater keeps running with an LC code, while newer ones can lock out until reset.

Riverside Public Utilities' 2025 water quality report lists hardness averaging 197 mg/L, about 12 grains per gallon. The 2025 report for EMWD's Mills area, which includes Moreno Valley, lists 5.1 to 7.5 grains per gallon, varying by source. Water that hard makes yearly descaling sensible, and a softener can cut the load further. See the pages on hard water scale prevention and installing a softener.

How is a Rinnai flush done?

Using hoses on the service valves, Rinnai's method circulates roughly four gallons of straight white vinegar through the heat exchanger, a process that can run up to 45 minutes. Rinnai says never to use chemical solutions. The service valves, the hoses and the water filter all have to be reconnected correctly afterward.

Hoses from the two service valves to a vinegar bucket, with a pump moving the solution.

Many owners prefer to hire it out because the gas and water must be shut and the valves opened in the right order. A plumber who flushes tankless units on a schedule will also inspect the vent and condensate collector, which are worth checking too.

If your heater is a condensing model, ask whether the condensate line and neutralizer are included in the visit. For a broader look at tankless care, see tankless water heater repair.

Is a Rinnai worth repairing or replacing?

Repair usually wins when the cause is scale, a dirty filter, a loose connection or a failed sensor. Replacement is worth discussing when the heat exchanger is damaged by lime, the unit has had repeat failures, or the gas and venting no longer meet code. A plumber can compare both options in one written quote.

A heater that has never been flushed may already carry scale damage, and age counts too, so check Rinnai's documents and your model's warranty. Sizing, venting and gas lines appear in Rinnai installation, and tankless versus tank suits anyone considering a switch.

A full replacement generally needs a Riverside permit, and Building and Safety, (951) 826-5800, can confirm for your address.

Which faults require a plumber at the unit?

Call if code 11 or 12 keeps returning after the simple checks, if an LC code appears on a heater with no flush history, or if you notice a gas odor or water dripping from the cabinet. Plumbers experienced with tankless units read the code, test gas pressure and the vent run, and service the heater.

We do not do the work ourselves. Request a written quote and we pass the job to a local plumbing business. Include the model number and the code on the display, so the right business takes the request. Everything else we handle is listed on the Rubidoux Ridge Plumbing home page.

Rinnai says alterations to a unit can void its warranty, so look at your paperwork before paying for a repair out of pocket.

Common questions

How long should a Rinnai repair take?

A flush, a filter cleaning or a sensor swap often fits in one visit. Ordering a part, or correcting gas or venting, stretches that out. Request a time window from the plumber, and find out whether the heater will stay off overnight until the work is finished.

Which questions suit a plumber doing Rinnai work?

Confirm they service Rinnai units, how they read the code on your display, what the quote covers, and if it includes a flush. Ask about parts supply, the permit if one applies, and the warranty on the labor, all in writing.

Is someone required at home?

An adult should let the plumber in and show the heater, the gas valve and the water shutoff. The plumber needs space around the unit and may turn gas and water off for some time. Report the code you saw and what you already tried.

Sources used

Page updated