Open the hot tap at a bathroom or kitchen sink. Hot water there means the heater works and the trouble sits in the shower valve or cartridge. Cold water at the sink as well means the heater, or the fuel feeding it, has quit. This single test cuts the problem in two. The heater side gets more depth on the water heater repair page.
Is the problem limited to the shower or house-wide?
First try two or three other hot taps. Hot at the sink with a cold shower implicates the shower valve, cartridge or mixing valve. Cold at every tap means the water heater is down, the hot reserve is spent, or a part on the supply side has failed.
Note the timing too. A shower that turned cold midway suggests the tank ran dry, because long or back-to-back use emptied the hot supply. One that stayed lukewarm for weeks before dying points to a valve or a heating element. Sudden loss accompanied by a gas smell is a safety matter and a separate case.
Pipe length counts as well. A bathroom far from the heater may need a minute or more to deliver hot water, and that lag is normal. Give it two minutes before concluding the shower is truly cold.
Why is the shower cold while the sinks run hot?
The usual suspects are a worn mixing cartridge, a clogged cartridge screen, or a failed thermostatic or pressure-balance valve. These parts mix hot with cold. If mineral scale blocks one side, or the cartridge has worn out, the mix tilts cold. Fitting a new cartridge made for your valve brand often solves it.
Hard water plays a part. The 2025 Riverside Public Utilities report gives average hardness of 197 mg/L, roughly 12 grains per gallon, so scale can clog a cartridge over time. Closing the valve stops, pulling off the trim and cleaning the screen is a home job for anyone comfortable with it.
A fault inside the wall is a different matter. When a new cartridge changes nothing, or the valve body leaks, read about a shower leak plumber and fixing a leaky shower faucet. Hot and cold lines cross-connected in an old valve can also push the hot side backward, and that needs a plumber.
What should I do when no tap in the house has hot water?
Begin with power or fuel. For an electric heater, look at the breaker and at the reset button on the upper thermostat panel. For a gas heater, confirm the pilot or igniter flame through the viewing window and make sure the gas valve is open. A unit that will not light after one careful try is your cue to stop and phone a plumber.
A gas smell means get out of the building, phone SoCalGas on 1-800-427-2200 from outside, and dial 911 if you feel threatened. Never relight a pilot where the room smells of gas. On tankless units, a code shown on the display is the first clue, and the manual decodes each one.
Further causes are listed in why you might have no hot water and a heater that works but gives no hot water.
How can I tell if a heating element or thermostat died?
Electric tank heaters carry two elements. When the upper one fails there is no hot water whatsoever, and when the lower one fails you get only a little hot water that is gone fast. A gas heater goes cold when the thermocouple, igniter or gas control fails. A tank that stays cold and silent after the power check usually has a dead part.
Checking an element takes a multimeter and the power cut at the breaker. If you do not own one, leave it alone. Replacing an element is a modest repair, described under water heater element replacement. On gas models the matching part is covered in thermocouple replacement.
Sometimes an older tank should simply be replaced. When it has outlived its normal lifespan, leaks at the base, or rumbles with sediment, a repair buys little. Plumber for water heater replacement shows how that decision is made.
Might the thermostat setting or sediment explain it?
Yes. A thermostat set too low produces lukewarm showers. The heater's label or manual states the maker's suggested setting, and a lower setting cuts scald risk. Raise it only in small steps, and keep hot water away from small children and elderly people, because higher temperatures burn skin fast.
Sediment is the other candidate. Hard water deposits mineral layers on the tank floor, shielding the water from the burner or element and shrinking capacity. A flush helps if none has happened in years, though an old tank may have a drain valve that sticks or starts leaking once opened. When unsure, call a plumber instead of forcing anything.
Homes in the Wood Streets, Arlington or the Eastside often have older heaters, so weigh age, because a tank close to retirement is a poor repair investment. A newer heater in Orangecrest or east Moreno Valley more likely has one failed part rather than a dead unit.
What to do next
Do the sink test, note gas or electric, check the breaker or pilot, and look around the tank base for water. Found a leak? Close the cold supply to the tank and the fuel, then call. Photograph the data label on the heater so the plumber can bring the right part.
When the repair goes past a cartridge or a reset, send a request and we pass it to a local plumbing business. Meanwhile, a hot kettle gives you wash water. The home page lists every job we cover, and emergency plumbing applies if water is leaking.
When to call a plumber business
Phone in if the heater leaks, a gas heater will not stay lit, the breaker keeps tripping on an electric unit, a new cartridge fails, or you cannot tell which part is at fault. In California, a contractor license is needed for any job requiring a permit; the City of Riverside's exempt-work handout leaves water heaters off the exempt list, so confirm with Building and Safety on (951) 826-5800.
In one visit a plumber can test the valve, the element or the gas control and write a quote for the part or a replacement. Request the license number, the visit cost, and whether the part's maker offers any warranty on the repair.
Common questions
What is the repair time for a shower with no hot water?
Which questions are worth asking before booking a no-hot-water visit?
Must an adult be on site during the repair?
Why is my shower hot for a minute and then cold?
Sources used
Page updated