Jump to content
Call us (951) 749-6477

Guide ยท Riverside

Shower water pressure is low: what to check, in order

If only the shower is weak, the fix is usually in the showerhead, the valve behind the wall or the diverter. If every fixture is weak, look at the whole house. This page tells the two cases apart.

Shower plumbing from the valve up to the head, with a flow restrictor inside the head and a diverter.

Turn on another faucet in the house. Quick filling at the sink and toilet with a feeble shower means the trouble is inside the shower itself, for instance scale in the head, a tired cartridge or a faulty diverter. Weakness at every fixture means the house supply or the street is to blame. For related services, read about faucets, sinks, showers and disposals, or browse everything from the home page.

Why is only my shower pressure low?

Because the cause sits between the shower valve and the spray holes. Scale inside the showerhead, a flow-limiting insert, a failing cartridge or a stuck tub-to-shower diverter can each cut the flow even though the rest of the house runs normally. The fix is usually quick and cheap, and it starts with the showerhead.

Unscrew the showerhead and look at the inlet screen and the holes. White or green crust means scale. Water in the Riverside area is hard: Riverside Public Utilities' 2025 report lists hardness averaging 197 mg/L, about 12 grains per gallon. Eastern Municipal Water District's 2025 Mills-area table lists averages of 5.1 to 7.5 grains per gallon. Scale clogs small spray holes first.

What is the best way to descale a clogged showerhead?

Take the head off, tie it in a bag of white vinegar with the face submerged, and let it soak one to two hours. Next, scrub the nozzles using an old toothbrush, rinse, and put it back with new pipe tape on the threads. EPA says a showerhead should connect tightly to the pipe stem and be sealed with tape.

Never use harsh acids on brass or special finishes, because they strip the coating. If the head is old, an inexpensive replacement is often better than another cleaning. EPA's WaterSense label marks showerheads that meet its flow and performance tests, so you can look for it when you shop. If the new head still gives weak flow, the problem is behind the wall.

Could the flow restrictor or diverter be the cause?

Yes. Many showerheads have a small plastic flow restrictor disc inside the inlet that limits flow, and mineral flakes can block it. A tub-and-shower valve has a diverter that sends water to the head or the spout, and a worn diverter can leak water to the tub and starve the shower.

Water pouring from the tub spout while the shower runs means the diverter is failing to seat. On some tubs the diverter is the pull-up knob on the spout, and replacing the spout fixes it. On others it is inside the valve, and a plumber has to replace parts behind the wall. The same valve parts appear in the guide to a dripping shower faucet.

Is a worn shower cartridge the culprit?

A shower valve cartridge controls both flow and temperature, and when it wears or scales up, the flow drops and the temperature drifts. A single-handle valve that has weak flow at every setting, or that sticks, has a cartridge due for replacement. Replacement means turning off the water, removing the handle and trim and pulling the old cartridge.

Shower valve cutaway with the cartridge in place, a worn area marked, and hot and cold inlets.

Brands differ, so match the new part to the old, and photograph the valve before taking it apart. Many valves have a built-in stop, and if the shower supply will not close, use the main shutoff. Delta single-handle valves have their own repair steps in the guide to a leaking Delta shower faucet. EPA notes that for valve leaks that drip when the shower is off, a plumber or an experienced handyperson is the recommended route.

Is the problem the whole house instead?

If the sink, tub and toilet are weak as well, the problem is the house supply. A main valve that is not fully open, a failing pressure regulator or old galvanized pipe can each reduce pressure throughout the house. Section 608.2 of the California Plumbing Code caps pressure at 80 psi, and a gauge screwed onto an outdoor hose bib shows the reading.

Pressure also depends on where you live. How high your home sits and how far it is from the supply can change what reaches the tap, so ask your water utility if low pressure seems to hit the whole street. Homes with older steel pipes may have restricted lines. Read about the causes of weak pressure and how to adjust the pressure regulator valve.

What if the hot side is weak but the cold side is fine?

Then the problem is in the hot water system, not the shower. Heater sediment, a valve left partway shut or a scaled tankless unit restricts hot water alone. The weak hot water page walks through those checks, and the guide on a shower with only cold water covers the opposite problem.

Book a plumber quote

Tell us about the job. We'll arrange a visit and a written quote before any work starts.

Lets the business see where the job is before they quote.

We earn a referral fee from the plumber who gets your job. You pay us nothing.

At what point is a plumber the answer?

Call if cleaning the showerhead changes nothing, if water shows up behind the wall or as a stain on the ceiling below, if the valve will not shut off, or if pressure is low across the house. A shower leaking inside the wall needs prompt repair, and our shower leak page explains the signs.

If the whole house is affected, the page on plumbers for low water pressure lists what a plumber checks. The plumber business that takes your request will quote in writing. The EPA puts the waste from a showerhead leaking 10 drips each minute at over 500 gallons a year, so a drip at the shower is worth fixing too.

Common questions

How much time does a low shower pressure fix need?

Cleaning a showerhead takes about an hour, mostly soaking. Swapping a cartridge or diverter takes longer than cleaning the head, and a pipe or regulator fault takes longer still. The plumber business that takes your request gives its own timing when it quotes the work.

What belongs on my checklist before hiring for low shower pressure?

Check that the visit includes a pressure reading, that the quote names the part, whether opening a wall is likely and who patches it, and get the contractor license number so you can verify it at cslb.ca.gov. Mention if other fixtures are weak, since that changes where the plumber starts looking.

Should I stay home while the plumber works on the shower?

Yes, an adult needs to be there to open up the bathroom, the shower and the water shutoff. Expect the water to be off for some of the visit. Empty the tub and shelves, and share what you have already tried, chemical cleaners included, so the plumber can work safely.

Can I make low pressure better with a booster pump?

Sometimes, but a pump should come after the cause is found. A pump forces more water past the same restriction, and it can strain old pipe. Check the showerhead, the valve and the house pressure first. If the supply is itself weak, a plumber can say whether a booster pump fits your house.

Sources used

Page updated